IECEx Approved Spring Loaded Thermocouples

with a choice of Terminal Heads

Send Enquiry Data Sheet Request Info

Also available with ATEX Approval

These semi rigid IECEx approved spring loaded thermocouples are supplied with an IP68 terminal head and threaded flameproof extension and are ideal for installation in thermowell pockets and where good contact with the process is required.They can be used with service temperatures up to 1250ºC (minimum stand-off lengths shown on here must be observed).

Available in a wide range of protection concepts for Zones 0, 1 & 2 use. See table below for details
Temperature classification T6-T1, see here for stand-off requirements
Available in thermocouple types K, T, J, N, E, R, S and B

Sheath diameters from 4.5mm to 8.0mm in a wide choice of materials
Insulated measuring junction gives a floating output with high insulation resistance
Spring loaded thermocouple insert with wide choice of process connections
UKAS calibration available.

Available with the following approvals:

Protection Type	Description	Zone
Ex nA IIC Gc	Non-Sparking (Gas)	2
Ex d IIC Gb	Flameproof (Gas)	1
Ex ia IIC Ga / IIIC Da	Instrinsically Safe (Gas/Dust)	0/20
Ex ib IIC Gb / IIIC Db	Intrinsically Safe (Gas/Dust)	1/21
Ex tb IIIC Db	Enclosure (Dust)	21
Ex tc IIIC Dc	Enclosure (Dust)	22

Enquiry Form

1. Thermocouple Type

2. Protection Concept

Concept Type	Select
Ex d Flameproof/Explosion Proof
Ex ia Intrinsically Safe
Ex ib Intrinsically Safe
Ex nA Non-Sparking
Ex tb Enclosure
Ex tc Enclosure

Your chosen concept is:

Ex d Flameproof/Explosion Proof – Category 2, Zones 1,2 (Gas)
• Ex d IIC T6...T1 Gb Ta = –40°C to 60°C
• Standard EN IEC 60079-1 refers
• Designed to contain an explosion and quench the flame
• Sensors incorporate a suitable heavy duty enclosure or threaded fitting with tight seals

Your chosen concept is:

Ex e Increased Safety – Category 2, Zones 1,2 (Gas)
• Ex e IIC T6...T1 Gb Ta = –40°C to 60°C
• Standard EN IEC 60079-7 refers
• Design ensures no arcs, sparks or hot surfaces that could ignite an explosive mixture with a minimum IP54 enclosure rating
• Sensors incorporate a suitable heavy duty enclosure or threaded fitting with tight seals

Your chosen concept is:

Ex ia Intrinsically Safe – Category 1, Zones 0,1,2 (Gas) & 20,21,22 (Dust)
Available for assemblies with Stainless Steel Terminal Heads
• Ex ia IIC T6...T1 Ga Ta = –40°C to 60°C
• Ex ia IIIC T80°C…T440°C Db
• Standard EN IEC 60079-11 refers
• Designed to limit the energy of arcs or sparks that could potentially ignite an explosive mixture
• Sensors used in this area must be wired through a suitably approved barrier
• Optional approved 4 to 20mA transmitters available

Your chosen concept is:

Ex ib Intrinsically Safe – Category 2, Zones 1,2 (Gas) & 21,22 (Dust)
Available for assemblies with Die Cast Alloy Terminal Heads
• Ex ib IIC T6...T1 Gb Ta = –40°C to 60°C
• Ex ib IIIC T80°C…T440°C Db
• Standard EN IEC 60079-11 refers
• Designed to limit the energy of arcs or sparks that could potentially ignite an explosive mixture
• Sensors used in this area must be wired through a suitably approved barrier
• Optional approved 4 to 20mA transmitters available

Your chosen concept is:

Ex nA Non-Sparking – Category 3, Zone 2 (Gas)
• Ex nA IIC Gc T6…T2
• Standard EN IEC 60079-15 refers
• No arcs, sparks or hot surfaces

Your chosen concept is:

Ex tb Enclosure – Category 2, Zones 21, 22 (Dust)
• Ex tb IIIC T80°C…T440°C Db
• Standard EN IEC 60079-31 refers
• Protects against combustible and conductive dusts, rugged tight enclosures are used

Your chosen concept is:

Ex tc Non-Sparking – Category 3, Zone 22 (Dust)
• Ex tc IIIC T85°C...T450°C Dc
• Standard EN IEC 61241 refers
• Protects against combustible dusts
• Sensors incorporate a suitable heavy duty enclosure with IP6X seal

3. Sheath Material

4. Sheath Diameter

5. Overall Sheath Length ( 'L')

mm*

6. Types of Sensing Junction

Illustration	Select
INSULATED Junction
Duplex Element Required? (please tick box)
Triplex Element Required? (please tick box)

7. Terminal Head

8. Extension Piece Length ( 'L1')

mm*

9. Process Thread

10. Optional (Rotating Union) Fitting

11. Optional 4 to 20mA Transmitter

12. Quantity Required

Qty Required

Contact Details

Company Name

Your Name

Email

Telephone

Additional Information

If your enquiry is for more than one style of sensor, please email us with your requirements or use the box below

Send Enquiry

1	Thermocouple Type	Temperature Range (continuous)	Temperature Range (short term)
K	Nickel Chromium vs Nickel Aluminium	0°C to +1100°C	-180°C to +1350°C
T	Copper vs Constantan	-185°C to +300°C	-250°C to +400°C
J	Iron vs Constantan	+20°C to +700°C	-180°C to +750°C
N	Nicrosil vs Nisil	0°C to +1100°C	-270°C to +1300°C
E	Nickel Chromium vs Constantan	0°C to +800°C	-40°C to +900°C
R	Platinum - 13% Rhodium vs Platinum	0°C to +1600°C	-50°C to +1700°C
S	Platinum - 10% Rhodium vs Platinum	0°C to +1550°C	-50°C to +1750°C
B	Platinum - 30% Rhodium vs Platinum 6% Rhodium	+100°C to +1600°C	+100°C to +1820°C
Temperature ranges refer to the thermocouple type. The temperature range of the sensor may deviate from the above, please refer to the product description for more details

2	Sheath Material	Max. Temperature
Standard Sheath Materials
321	321 Stainless Steel	800°C
310	310 Stainless Steel	1100°C
600	Inconel 600	1100°C
Specialized Sheath Materials
114	Nicrotherm D^TM	1250°C
156	Hastelloy X	1220°C
446	AISI 446	1150°C
800	Incoloy 800	1100°C

Products

Temperature Sensors

Temperature Instrumentation

Temperature Accessories

Calibration

FREE Guide

Literature Request

Further Information

IECEx Approved Spring Loaded Thermocouples

with a choice of Terminal Heads

Enquiry Form

1. Thermocouple Type

2. Protection Concept

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

3. Sheath Material

4. Sheath Diameter

5. Overall Sheath Length ( 'L')

6. Types of Sensing Junction

7. Terminal Head

8. Extension Piece Length ( 'L1')

9. Process Thread

10. Optional (Rotating Union) Fitting

11. Optional 4 to 20mA Transmitter

12. Quantity Required

Contact Details

Additional Information