IECEx Spring Loaded RTD Pt100 Sensors

These spring loaded flexible mineral insulated platinum resistance thermometers utilise, as standard, detector elements with a resistance of 100 ohms @ 0°C and a fundamental interval of 38.5 ohms to IEC 60751. The threaded flameproof extension is ideal for installation in thermowell pockets and where good contact with the process is required.

Available in a wide range of protection concepts for Zones 0, 1 & 2 use. See table below for details
Temperature classification T6-T1, see here for stand-off requirements
Available in B, A, 1/3, 1/5 and 1/10 grade accuracies

Sheath diameters from 0.188" to 0.313"
Spring loaded RTD Pt100 insert with wide choice of process connections
Wide operating temperature range of -328°F to +1112°F
UKAS calibration available.

Available with the following approvals:

Protection Type	Description	Zone
Ex nA IIC	Non-Sparking (Gas)	2
Ex db IIC Gb	Flameproof (Gas)	1
Ex ia IIC Ga / IIIC Da	Intrinsically Safe (Gas/Dust)	0/20
Ex ib IIC Gb / IIIC Db	Intrinsically Safe (Gas/Dust)	1/21
Ex tb IIIC Db	Enclosure (Dust)	21
Ex tc IIIC	Enclosure (Dust)	22

Enquiry Form

1. No. of Elements

2. Protection Concept

Concept Type	Select
Ex db Flameproof/Explosion Proof
Ex ia Intrinsically Safe
Ex ib Intrinsically Safe
Ex nA Non-Sparking
Ex tb Enclosure
Ex tc Enclosure

Your chosen concept is:

Ex db Flameproof/Explosion Proof – Category 2, Zones 1,2 (Gas)
• Ex db IIC T6...T1 Gb Ta = –40°C to 60°C
• Standard EN IEC 60079-1 refers
• Designed to contain an explosion and quench the flame
• Sensors incorporate a suitable heavy duty enclosure or threaded fitting with tight seals

Your chosen concept is:

Ex e Increased Safety – Category 2, Zones 1,2 (Gas)
• Ex e IIC T6...T1 Gb Ta = –40°C to 60°C
• Standard EN IEC 60079-7 refers
• Design ensures no arcs, sparks or hot surfaces that could ignite an explosive mixture with a minimum IP54 enclosure rating
• Sensors incorporate a suitable heavy duty enclosure or threaded fitting with tight seals

Your chosen concept is:

Ex ia Intrinsically Safe – Category 1, Zones 0,1,2 (Gas) & 20,21,22 (Dust)
Available for assemblies with Stainless Steel Terminal Heads
• Ex ia IIC T6...T1 Ga Ta = –40°C to 60°C
• Ex ia IIIC T80°C…T440°C Db
• Standard EN IEC 60079-11 refers
• Designed to limit the energy of arcs or sparks that could potentially ignite an explosive mixture
• Sensors used in this area must be wired through a suitably approved barrier
• Optional approved 4 to 20mA transmitters available

Your chosen concept is:

Ex ib Intrinsically Safe – Category 2, Zones 1,2 (Gas) & 21,22 (Dust)
Available for assemblies with Die Cast Alloy Terminal Heads
• Ex ib IIC T6...T1 Gb Ta = –40°C to 60°C
• Ex ib IIIC T80°C…T440°C Db
• Standard EN IEC 60079-11 refers
• Designed to limit the energy of arcs or sparks that could potentially ignite an explosive mixture
• Sensors used in this area must be wired through a suitably approved barrier
• Optional approved 4 to 20mA transmitters available

Your chosen concept is:

Ex nA Non-Sparking – Category 3, Zone 2 (Gas)
• Ex nA IIC T6…T2
• Standard EN IEC 60079-15 refers
• No arcs, sparks or hot surfaces

Your chosen concept is:

Ex tb Enclosure – Category 2, Zones 21, 22 (Dust)
• Ex tb IIIC T80°C…T440°C Db
• Standard EN IEC 60079-31 refers
• Protects against combustible and conductive dusts, rugged tight enclosures are used

Your chosen concept is:

Ex tc Non-Sparking – Category 3, Zone 22 (Dust)
• Ex tc IIIC T85°C...T450°C
• Standard EN IEC 61241 refers
• Protects against combustible dusts
• Sensors incorporate a suitable heavy duty enclosure with IP6X seal

3. Number of Wires

4. Sheath Diameter

5. Overall Sheath Length ('L')

inches*

6. Tolerance of Element

Grade	Accuracy @ 0ºC	Accuracy @ 100ºC	Select
B	+/- 0.30ºC	+/- 0.80ºC
A	+/- 0.15ºC	+/- 0.35ºC
1/3	+/- 0.08ºC	+/- 0.19ºC
1/5	+/- 0.05ºC	+/- 0.15ºC
1/10	+/- 0.03ºC	+/- 0.12ºC

7. Terminal Head

8. Extension Piece Length ( 'L1')

mm*

9. Process Thread

10. Optional (Rotating Union) Fitting

11. Optional 4 to 20mA Transmitter

12. Quantity Required

Qty Required

Contact Details

Company Name

Your Name

Email

Telephone

Additional Information

If your enquiry is for more than one style of sensor, please email us with your requirements or use the box below

Send Enquiry

Products

Temperature Sensors

Temperature Instrumentation

Temperature Accessories

Calibration

FREE Guide

Literature Request

Further Information

IECEx Spring Loaded RTD Pt100 Sensors

with a choice of Terminal Heads

Enquiry Form

1. No. of Elements

2. Protection Concept

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

Your chosen concept is:

3. Number of Wires

4. Sheath Diameter

5. Overall Sheath Length ('L')

6. Tolerance of Element

7. Terminal Head

8. Extension Piece Length ( 'L1')

9. Process Thread

10. Optional (Rotating Union) Fitting

11. Optional 4 to 20mA Transmitter

12. Quantity Required

Contact Details

Additional Information

Wiring Diagram Sheath Materials